INDUSTRIAL · Latur, Maharashtra
Industrial & Commercial
Sheds, workshops, showrooms and plants — three-phase work planned around your production window, not ours.
01 / Scope
What we actually do on site.
1.1
Panel fabrication
Main and sub-distribution panels built to load schedule, with starters, contactors and overload protection.
1.2
Motor control
DOL and star-delta starters, VFD installation and interlocks for pumps, compressors and machine lines.
1.3
Cable management
Cable trays, conduit runs and busbar layouts routed for access and future expansion.
1.4
Power quality
Phase balancing, capacitor bank checks and voltage-drop measurement on long runs.
1.5
Shutdown planning
Staged work with defined isolation, so downtime is scheduled and short.
1.6
Thermal inspection
Periodic checks of joints and terminations to catch heating before it becomes a failure.
02 / Single-line
How the industrial circuit is drawn before it is built.
Cable trays route all feeder runs between panel and motor loads, sized with spare fill capacity
- HT / LT incomer — Utility or transformer
- Main panel — Bus-bar, metering
- MCCB — Feeder protection
- Starter / VFD — DOL, star-delta or drive
- Motor load — Pump, compressor, line
03 / Process
Planned around your production window.
01
Load and utilisation study
Machine-by-machine load list with duty cycles, so panels and cables are sized for how the plant actually runs.
1–3 days·Machine load list with duty cycles
02
Panel design
Schedule and layout for main and sub-distribution boards, starters, VFDs and protection coordination.
3–7 days·Panel general arrangement + protection schedule
03
Shutdown plan
Isolation points, staged sequence and the exact window agreed with your production team before work starts.
Agreed before mobilisation·Written shutdown sequence and window
04
Execution
Panels, cable trays, conduit runs and busbar work installed to the layout, with access left for expansion.
Scoped to the shutdown window·Installed panel and cable-tray runs
05
Power quality check
Phase balancing, capacitor bank verification and voltage-drop measurement on long runs.
Half to full day·Power quality measurement report
06
Thermal audit
Joints and terminations imaged under load to catch heating before it becomes a failure.
Half day, under normal load·Thermal image report with flagged joints
04 / Specification
What goes into the bill of materials, and why.
| Item | Standard we specify | Why it matters |
|---|---|---|
| Main panel | IP-rated sheet-steel enclosure, bus-bar sized to incomer rating with fault-current withstand | The main panel carries the full plant load; under-sizing the bus-bar is a fire risk under fault conditions. |
| Feeder protection | Schneider / Legrand / Havells-class MCCB, selectively coordinated with upstream and downstream devices | Coordinated protection trips the nearest breaker to a fault, not the main incomer — keeps the rest of the plant running. |
| Motor starters | DOL or star-delta starters, or VFDs, sized to motor FLC with thermal overload protection | An overload relay set to the wrong current either nuisance-trips or fails to protect the motor windings. |
| Cabling | XLPE/PVC armoured power cable on galvanised cable trays, power and control segregated | Segregating power and control cabling avoids induced noise on sensor and PLC wiring. |
| Power factor correction | Capacitor banks sized to measured reactive load, with detuned reactors where VFDs are present | Uncorrected power factor draws penalty charges from the DISCOM on a commercial connection. |
| Earthing | IS 3043 earthing, separate pits for body earth and electronic/VFD earth | Mixing power and electronic earths on sensitive drive equipment causes nuisance faults and drive damage. |
- Main panel
- IP-rated sheet-steel enclosure, bus-bar sized to incomer rating with fault-current withstand
- The main panel carries the full plant load; under-sizing the bus-bar is a fire risk under fault conditions.
- Feeder protection
- Schneider / Legrand / Havells-class MCCB, selectively coordinated with upstream and downstream devices
- Coordinated protection trips the nearest breaker to a fault, not the main incomer — keeps the rest of the plant running.
- Motor starters
- DOL or star-delta starters, or VFDs, sized to motor FLC with thermal overload protection
- An overload relay set to the wrong current either nuisance-trips or fails to protect the motor windings.
- Cabling
- XLPE/PVC armoured power cable on galvanised cable trays, power and control segregated
- Segregating power and control cabling avoids induced noise on sensor and PLC wiring.
- Power factor correction
- Capacitor banks sized to measured reactive load, with detuned reactors where VFDs are present
- Uncorrected power factor draws penalty charges from the DISCOM on a commercial connection.
- Earthing
- IS 3043 earthing, separate pits for body earth and electronic/VFD earth
- Mixing power and electronic earths on sensitive drive equipment causes nuisance faults and drive damage.
Standard we specify
Why it matters
Standard we specify
Why it matters
Standard we specify
Why it matters
Standard we specify
Why it matters
Standard we specify
Why it matters
Standard we specify
Why it matters
05 / Why us
Why industrial work goes wrong — and how we avoid it.
Downtime is scheduled, not discovered
Isolation and sequence are agreed in writing before anyone opens a panel, so the line restarts when we said it would.
Protection coordinated
Upstream and downstream devices selected together, so a fault trips the nearest breaker and not the main.
Built for the next machine
Spare ways, tray capacity and cable routes planned for the load you add next year.
06 / Continue the current
The rest of the spine.
01 / SOLAR
Solar Solutions
Rooftop generation designed against your actual load, not a brochure size.
See scope02 / ELECTRICAL
Electrical Contracting
The spine of the building: wiring, distribution boards, earthing, protection.
See scope04 / LIGHTING
Lighting Solutions & Maintenance
Lighting that is planned for lux and lifespan — and kept running after handover.
See scope07 / Next step
A free survey, then honest numbers.
Tell us where you are and what you need. We come, we measure, and we quote what the building actually requires.
+91 78881 58812 · Latur, Maharashtra, India